Skip to content

RECTILINEAR PROPAGATION AND REFLECTION AT PLANE SURFACES. INTRODUCTION

Objects that produce their own light are known as luminous objects i.e. the sun, torch lamps etc. objects that do not produce their own light are called non-luminous objects i.e. the moon. Opaque objects are those which do not allow light to pass through them. Translucent materials are those which allow light to pass through them but we cannot see through them i.e. church glass and bathroom glass.

 

Transparent materials are those which allow light to pass through them and we can see through them i.e. window panes, car windows etc. A ray is the direction of the path followed by light. A beam is a group of rays travelling together.

Experiment: light travels in straight lines

Procedure

  1. Obtain three cardboards with a hole at the center and mount them such that they form a straight line.
  2. Arrange them as shown and place a lighted candle at one end and make sure that you can see the flame from the other end.
  3. Move any of the cardboards and observe what happens.

 

Discussion

When one cardboard is displaced or moved slightly the flame cannot be seen at the other end. This shows that light travels in a straight line. This principle is applied in the following, Pinhole camera It consists of a closed box with a small hole on one face and a screen of tracing paper/ frosted glass on the opposite face as shown. An image will be formed on the screen.

 

Since light travels from one point of the object through the hole an image will be formed on the opposite screen of the box. If the object is near the hole it is magnified while diminished if away from the hole. Magnification is therefore the ration of the image to object height , expressed as,

Magnification = height of image/ height of object or

= distance of image from pinhole/ distance of object from pinhole

Shadows

Shadows are formed when an opaque object is placed between a source of light and a screen. When the shadow is big a dark patch at the centre is formed (umbra) while a surrounding lighter patch called penumbra is formed.

Eclipses Eclipse of the sun (solar eclipse) This occurs when the moon is between the earth and the earth.

See also  PRESSURE

The shadow of the moon falls on the earth’s surface. Sometimes the distance is large for the shadow to reach the earth and when this happens an annular eclipse occurs.

 

Annular eclipse

Eclipse of the moon

It is also known as lunar eclipse and occurs when the earth is between the sun and the moon. The shadow of the earth falls on the moon.

 

Examples

  1. Calculate the height of a building 300 m away from a pinhole camera which produces an image 2.5 cm high if the distance between the pinhole and the screen is 5.0 cm.

Solution

Object distance = 300 m, image height = 2.5 cm, image distance = 5.0 cm. Object

height/ image height = object distance/ image distance

Object height = (30,000 × 2.5) / 5.0 = 15,000 cm = 150 m.

  1. The length of a pinhole camera is 25.0 cm. An object 2.0 cm is placed 10.0 m from the pinhole. Calculate the height of the image produced and its magnification.

Solution

Image height = (image distance × object height) / object distance

= (25 ×200) / 10 = 500 cm or 5 m. Magnification = image distance / object distance = 25 /10 = 2.5

 

Reflection from plane surfaces

Diffuse and regular reflection

Regular reflection occurs when a parallel beam of light falls on a plane mirror band reflected as a parallel beam. They occur on polished surfaces. A diffuse reflection occurs on rough surfaces where a parallel beam of light is reflected in all directions.

 

Laws of reflection

  1. The incident ray, the normal and the reflected ray at the point of incidence must be on the same plane
  2. The angle of incidence is equal to the angle of reflection.

I mages formed by reflection from plane surfaces

Characteristics of images formed in a plane mirror

  1. The image is the same size as the object
  2. The image is the same distance behind the mirror as the object is in front
  3. The image is laterally inverted
  4. The image is virtual
  5. The image is erect.
See also  MEASUREMENT IN PHYSICS

 

Location of an image by the non-parallax method

Parallax is the apparent relative motion of two objects due to the movement of the observer. It only occurs when the objects are at a distance from one another. This can be used to find the position of images in plane mirrors.

Experiment: To find the position of an image of a pin by non-parallax method

Procedure

  1. Obtain a sheet of paper and draw a mirror line
  2. Place the mirror on the line as shown
  3. Place the pin at least 5 cm from the mirror and obtain another pin (search pin)
  4. Move the pin till you get a point where there is no parallax and place your second pin.
  5. Measure the distances (both image and object) and confirm your results.

 

Mirrors at an angle

When mirrors are placed at an angle several images are obtained depending on the angle between them. If the angle is 600 the images formed will be five. We use the following formula to find the number of images.

= (360o / θ) – 1

When mirrors are parallel then the images formed are infinite.

 

Kaleidoscope

It applies the principle of mirrors at an angle. Consists of two mirrors arranged at an angle of 600 to one another inside a tube. The bottom has a ground-glass plate with brightly coloured glass for allowing light. When one observes through the tube five images are seen.

 

The periscope

This consists of two mirrors arranged at an angle of 450 as shown. This principle is used in periscopes (prisms) and telescopes.

 

See also:

HEAT TRANSFER

THERMAL EXPANSION

PARTICULATE NATURE OF MATTER

PRESSURE

FORCES

SUBSCRIBE BELOW FOR A GIVEAWAY

Building & maintaining an elearning portal is very expensive, that is why you see other eLearning websites charge fees. Help to keep this learning portal free by donating or supporting us. We accept grants, sponsorships & support to help reach out to more people. Thank you so much. Click here to donate

Leave a Reply

Your email address will not be published.

School Portal NG
error: Content is protected !!