RATE OF REACTION | MEANING, WAYS, RATE CURVE & COLLISION THEORY - 2024

MEANING OF RATE OF REACTION

The rate of a chemical reaction is the number of moles of reactants converted or products formed per unit time. Usually, rate of reaction is determined experimentally by measuring change in concentration of one of the components in the reaction with time.

Table of Contents

Thus,

Rate of reaction = change in concentration of reactant or product (mol/dm³)

Time taken for the change (seconds)

Get A Free USA Scholarship, Visa & Accommodation

The unit of the rate of reaction is mol/dm^-3s^-1 or g dm^-3s ^–1.

Rate of reaction can also be expressed as:

Rate of reaction = change in number of mole or mass of reactant or product

Time taken for the change

Then the unit of rate is mols^-1 or gs^-1

EXAMPLE: When 0.5g of calcium trioxocarbonate (IV) was added to excess dilute hydrochloric acid, carbon (IV) oxide was evolved. The complete reaction took 5 minutes. What was the rate of reaction?

Study in US, Canada, UK, Germany For Free

SOLUTION:

Rate of reaction = change in mass of reactant

Time taken for the change

= (0.5 – 0)g = 0.5

5×60 300

= 1.67 x 10^-3 gs^-1

WAYS OF MEASURING REACTION RATE

Concentration is one of the properties of a reaction that can change with time.

The following properties can also change with time and can thus be used to measure rate of reaction.

Decrease in mass of reaction system
Volume of gaseous product
Amount of precipitate formed
Change in colour intensity
Change in pH
Change in total gas pressure

FEATURES OF RATE CURVE

It passes through the origin. This is because there is no change in concentration or mass at the start of reaction.
It steeps at first, this because the rate is fast at the beginning.
It becomes less steep later. This is because the rate slows down.
It finally becomes horizontally. This is because the reaction has reached the end points.

The following can be determined from the rate curve

Average rate of reaction

Average rate = total number of mole / mass involved

Time taken

Rate at a particular instant during the reaction

Rate at instant = Gradient at a point on the curve

When the rate of reaction has direct variation with concentration, then

Rate of reaction α[Concentration of A]

R α [A]

R = k[A]

Where k is called Rate constant

EVALUATION

What is rate of reaction?
State two ways of measuring reaction rate

COLLISION THEORY

The collision theory states that for a chemical reaction to occur the reactant particles must collide and they must collide with a certain minimum amount of energy known as activation energy.

Reacting particles are in continuous motion, thus they possess energy and they also collide with one another. Not all collisions result into chemical reaction. Collisions, which result into chemical reaction, are called EFFECTIVE COLLISIONS. Minimum amount of energy required by reacting particles for chemical reaction to occur is called ACTIVATION ENERGY. Activation energy is the ENERGY BARRIER the reactants must overcome for reaction to occur. It is the minimum energy required for bond breaking for chemical reaction to occur.

Chemical reaction occur only when the energy of the colliding reactant particles is equal to or more than the activation energy. Activation energy must be equal to energy barriers also for chemical reaction to occur. Every reaction has its own energy of activation. Reactions with low activation energy have high rate of reaction and occur spontaneously. Reaction with high activation energy have low rate of reaction and are not spontaneous. The graph below illustrates the concepts of the activation energy for endothermic and exothermic reactions.

EXOTHERMIC REACTION ENDOTHERMIC REACTION

From graph, it can be seen that

Both exothermic and endothermic reactions generally require an initial input of energy to overcome the activation energy barriers.
Exothermic reaction once started proceed without any further external energy supply e.g burning of kerosene

3.Endothermic reaction proceeds with continuous supply of external energy e.g cooking of rice.

EVALUATION

State collision theory.
Graphically differentiate exothermic reaction from endothermic reaction.

FACTORS AFFECTING RATE OF REACTION

From the collision theory, it can be seen that rates of reaction depends on the following features.

The energy of the particle.
The frequency of collision of the reaction.
The activation energy of the reaction.

These features of a chemical reaction are in turn affected by some factors, which can make them to change and consequently affect the rate of reaction. These are factors that affect the rate of reactions. Some important ones are:

Nature of reactants.
Concentration / pressure (for gases) of reactants.
Surface area of reactants
Temperature of reaction mixture
Presence of light
Presence of catalysts

To study the effect of any one of these factors on rate of reaction all other factors must be kept constant.

EFFECT OF NATURE OF REACTANTS

If all other factors are kept constant, different substances will have different rate of reaction with dilute HCl, for example. When dilute HCl reacts with zinc, iron and gold under the same condition, hydrogen gas is evolved fast with zinc, slow with iron and no gas evolved with gold. The difference in rate of reaction is due to the chemical nature of the elements as they naturally posses different amount of energy content.

EFFECT OF CONCENTRATION OF REACTANTS

The frequency of collision among particles is high when the particles are crowded in a small space, i.e high concentration. This leads to high effective collision and thus high rate of reaction. An increase or decrease in the concentration of the reactants will result in corresponding increase or decrease in effective collisions of the reactants and hence the reaction rate.

EFFECT OF SURFACE AREA OF REACTANTS

This is a very important factor to be considered when a solid is involved in a chemical reaction. Lumped solids offer small surface area of contact for reaction while powdered solids offer large surface area for reaction. Rate of reaction is slow with lumped solid but high with powdered solids.

EFFECT OF TEMPERATURE

Increasing the temperature of a system can lead to an increase in reaction rate in two ways. When heat is raised, energy in form of heat is supplied to the reactant particles, so that

The number of particles with energy equal to or greater than the activation energy increases.
The velocity of all the reactant particles increases due to the greater kinetic energy, leading to a higher frequency of collision.

As a result, the number of effective collisions increases and the reaction proceeds at a faster rate. Decreases in temperature leads to decrease rate of reactions.

EFFECT OF LIGHT

Some reactions are influenced by light. The rate of reaction is high when the lights intensity is high, low when the intensity is low and does not proceed at all in the absence of light. Such reactions are known as photochemical reaction. Examples of photochemical reactions include.

Reaction between hydrogen and chlorine and
Decomposition of hydrogen peroxide
Reactions between methane and chlorine
Photosynthesis in plant
Conversion of silver halides to grey metallic silver.

EFFECT OF CATALYST

A Catalyst is a substance, which alters the rate of a reaction, but itself does not undergo any change at the end of the reaction.

A positive catalyst increases the rate of reaction by lowering the activation energy of the reaction whereas, the one which increases the activation energy is known as a negative catalyst or an inhibitor.

The diagram below illustrates the energy profile for catalyzed and uncatalyzed exothermic and endothermic reactions

EXOTHERMIC REACTION ENDOTHERMIC REACTION

GENERAL EVALUATION/REVISION

List and explain three factors that can affect the rate of reaction of the following reaction: CaCO_3(s) + 2HCl_(aq)→ CaCl_2(aq) + H₂O_(l) + CO_2(g)
In a chemical reaction, after 10seconds, 6moles from the initial concentration of 16moles of the reactant disappeared. Calculate the rate of the reaction.
State THREE characteristics of catalyst.
What is the volume in dm³ of 8g of oxygen gas at s.t.p?
Calculate the percentage of water in sodium trioxocarbonate (VI) heptahydrate

WEEKEND ASSIGNMENT

SECTION A: Write the correct option ONLY

The minimum amount of energy that colliding molecules must possess for their collisions to be effective is a. thermal energy b. collision energy
activation energy d. kinetic energy

2.Zn_(s) + H₂SO_4(aq) → ZnSO_4(aq) + H_2(g)

The rate of evolution of hydrogen gas in the above reaction will be greatly increased if a. the zinc is in the form of pellets b. a smaller volume of H2SO4 is used c. the reaction flask is immersed in an ice bath d. the zinc is in powdered form

The units of rate of reactions is moldm^-3s^-1 b. mol^-1s^-1 c. mol^-1 d. smol^-1
If 2g of zinc granules was reacted with excess dilute HCl to evolve hydrogen gas which

came to completion after 5min. Calculate the rate of the chemical reaction in ghr^-1

48ghr^-1 b. 12ghr^-1 c. 24ghr^-d d 240ghr^-1
What do we do to increase the surface area of solid reactants to high rate of reaction? a. grinding them into powder subjecting the reactants to high pressure c. altering the directing of the reaction d. using reactants of different densities.

SECTION B

1a. Define rate of reaction