MINING

Process of extracting valuable minerals from the earth’s surface.

Formations in Which Minerals Occur

  1. Veins and Lodes

– Occurrence of minerals in crevices, cracks or faults in igneous rocks.

  • They are said to occur in veins if they occur there in small quantities.
  • Said to occur in lodes if they occur there in large quantities e.g. zinc, copper and silver.
  1. Reefs

– Veins and lodes which are exposed on the surface.

  1. Seams/Layers/Beds

-Occurrence of minerals as sedimentary or as a result of compression of accumulated organic or inorganic material e.g. coal and halite.

  1. Alluvial Deposits

-Occurrence of miner als while mixed with materials such as sand, gravel, silt, etc.

These were minerals which were detached from the veins by weathering and carried away by streams and rivers and got deposited e.g. gold, diamond and platinum.

  1. Weathering Products

– Minerals formed by deep weathering of rocks then leaching carried minerals from the top to lower layers where they accumulated e.g. aluminium, nickel, iron and manganese.

  1. Oil pools/Wells

-Occurrence of minerals in pools or wells in sedimentary rocks e.g. petroleum and natural gas.

 

Conditions Necessary for Formation of Petroleum

  1. a) Presence of fossils or organic remains
  2. b) Presence of sedimentary rocks for burying organic remains.
  3. c) Presence of pressure to compress organic remains to cook the oil and natural gas out of organic matter.
  4. d) Presence of a porous reservoir rock to store and transmit petroleum to the oil pools e.g. limestone and sandstone.
  5. e) Presence of a trap like a syncline to hold petroleum in a reservoir to prevent its escape.
  6. f) Presence of impermeable rocks below the trap or syncline to prevent petroleum from percolating further underground.

 

Factors Influencing Exploitation of Minerals

  1. Value of Mineral

Minerals of high value will be mined even if they occur in small quantities because one sold it will be possible to offset mining costs and make a profit and vice versa.

  1. Quality of Ore

Mining can be done if the mineral deposits have high mineral content because they are economical to work on but deposits with low mineral content are rarely worked on except if the mineral in them is rare e.g. uranium.

  1. Size of Deposit

Minerals which aren’t of high value have to occur in large quantities for them to be mined so that it will be a possible to recover mining costs and make a profit.

  1. Capital

Lack of capital causes developing countries not to exploit minerals and leave it to international companies because a lot of money is needed for exploration, infrastructure, salaries, energy etc e.g. titanium mining at Kwale is being done by Tiomin company from Canada.

  1. Method of Mining

A mineral requiring open cast mining will be mined even if the mineral deposit is large but one requiring underground mining will be extracted if its in large deposit or if its of high value or rare.

  1. Transport costs

Minerals occurring in remote areas far from the markets are not likely to be exploited if the transport system is poorly developed since mineral ore is heavy and bulky and transporting it by road and railway is expensive.

  1. Market for the Mineral

Mining can be done if the mineral is in demand and if the prices are reasonable so that mining costs are offset and a profit is realised.

  1. Political Influence

Mineral deposits at the borders of two countries may not be exploited as a dispute may arise concerning whom mine it e.g. dispute between Iraq and Kuwait over Rumaila should oil field.

  1. Labour

Exploitation of some minerals require skilled workers and if they lack it may not be done as is the case in developing countries because expatriates have to be engaged and are very expensive to pay which may reduces the profits accruing from mining.

 

Methods of Mining

  1. Open Cast Mining

-Method of extracting minerals which are near the earth’s surface.

Types a) Stripping

-Stripping off of the unwanted material lying on top of the mineral deposit and then digging to remove the mineral bearing rock if it’s soft or if it’s hard explosives may be used to loosen it and then huge power shovels are employed to dig up the mineral deposits.

  1. b) Hill-slope Boring

-Using boring instruments known as augers to drill out mineral deposit and bring it to the surface.

  1. Underground Mining

-Method employed when the mineral lies very deep below the surface and the overburden is too thick to be removed by mechanical means.

 

Types

  1. a) Shaft Method

– Method employed when the mineral bearing rock doesn’t out crop.

How it’s carried out

  • Vertical shafts are sunk into the earth’s crust to reach the layer with the mineral.
  • Horizontal tunnels are dug from the vertical shaft to reach the mineral.
  • Props are erected to support the roof to prevent it from collapsing.
  • The mineral bearing rock is blasted loose by explosives.
  • The deposit is transported on light rail or conveyor belt to the bottom of the shaft.
  • It is then brought to the surface in a crane or a lift called cage.
  1. a) Drift/Adit Mining

-Method employed when the mineral deposit can be reached from the valley sides.

  • Horizontal tunnels (adits) are constructed from the side of the hill.
  • Railway line is constructed into the mine to bring out the mineral e.g. mining of copper at Kilembe in Uganda.
  1. b) Solution Method

– Method used in mining soluble minerals such as sulphur, salt, potash, etc.

15 Places to WIN $10,000
15 Places to WIN $10,000 Cash
  • Superheated water is ejected into salt deposits.
  • The mineral dissolves or melts.
  • The solution is then pumped into the surface.
  1. c) Drilling

-Method employed in exploitation of petroleum.

  • Wells (oil derricks) are drilled.
  • Oil and natural gas are brought to the surface under their own pressure or by pumping.
  1. Alluvial/Placer Mining

-Method used to extract minerals occurring in alluvial deposits e.g. gold, tin, diamonds and platinum.

 

Types

  1. a) Panning

It involves:

  • Digging a mixture of sand, gravel and mineral from the river bed.
  • Putting it in a pan and rotating the pan while tilted.
  • The lighter sand or gravel is washed on the side leaving the heavier mineral at the bottom of the pan e.g. gold mining in Migori and R. Morun Beds in W. Pokot.
  1. b) Dredging
  • A dredger scoops water logged alluvium from the bed of a lake.
  • The alluvium is passed over sloping channels with series of traps.
  • Wastes are washed away and denser materials are left at the bottom of the trap e.g.mining of soda ash at L. Magadi.
  1. c) Hydraulic Mining – Method used when alluvial deposit occurs on a valley side.
  • A powerful jet of water is directed at the deposit.
  • Gravel and mineral collect at the valley because of the great pressure.
  • The mineral grains are recovered and washed out.
  1. d) Sub-marine Mining

– Method employed in extracting minerals in alluvial deposits lying deep down the ocean floor.

  • A sub-marine dredger goes down the ocean floor.
  • It scoops mineral deposit and rises to the surface.
  • The alluvium is passed over sloping channels with series of traps.

• Wastes are washed away and denser materials are left at the bottom of the trap

 

See also

BUSH FALLOWING IN WEST AFRICA

NATURAL SATELLITES

THE EARTH AND THE SOLAR SYSTEM

GEOGRAPHY SS 1 SCHEME OF WORK

GEOGRAPHY PAST QUESTIONS

Leave a Comment

Your email address will not be published. Required fields are marked *

Get Fully Funded Scholarships

Free Visa, Free Scholarship Abroad

           Click Here to Apply

Acadlly